Firewire Priming
From MythTV Official Wiki
Contents
Introduction
Below are two firewire scripts which change channels and prime the firewire before MythTV starts to record. The first is for a one tuner setup and the second is a more flexible two tuner setup.
Both require the 6200ch helper program:
Required 6200ch change channel script
You also need the 6200ch change channel script which you can compile in the /usr/share/doc/mythtv-0.20/contrib/channel_changers directory (read the README). Don't forget you will need to get the headers for the kernel (yum install kernel-devel). On RedHat Fedora 5, you will also need the libavc1394-devel package, (yum install libavc1394-devel).
One Tuner Priming Script
This is a script which is invoked each time a channel change is requested and a firewire connection needs to be working. It first tests the existing p2p and channel settings and if OK, test to see if the result from test-mpeg2 is a non-zero file which means the firewire connection is working. If the result is negative for any of the p2p, channel and non-zero file tests, it then tries to use plugctl to reset the firewire connection, and then runs the test-mpeg2 test again. It repeats ten times and if it gets 10 non-zero results, it fails.
Note:
- It relies on the 6200ch change channel script.
- It assumes the firewire connection is on node 1 and p2p routing (not bcast).
- If your node is not 1, be sure to add the correct node in front of the channel change command. IE: '/home/6200ch -n2 $1' rather than '/home/6200ch $1'
- If you run mythbackend with a log file, i.e. "mythbackend >> /home/mythbackend_log.log &", the echo statements below will appear in the log which is useful for debugging.
#!/bin/bash
# v1.02, a Firewire change channel and test script by Sean Donovan, techonfoot.com
# Released under GPL, 2006
# Revision history
# v1.02 - Fixed the unnecessary kill_test.sh script
# v1.01 - Added detection for conditions that work intermittently, i.e. test-mpeg2 will work
# but the next capture by MythTV won't. Usually when p2p is 0 or channel <> 63.
# Fixed a bug whereby the script expects the kill_test.sh script in the /home directory.
# v1.00 - Genesis
#
# ------------------------
# Prime the variables used to exit the while loop and set error messages
# C2 is used to avoid the while loop or exit it, if the firewire is primed
# C3 is used to notify either an error condition (=1) or not (=0)
C2=0
C3=1
# Change the channel
/home/6200ch $1
# Then change into the directory with the kill_test.sh script
cd /home
# First check to make sure the firewire port is set up correctly or the
# "Is it primed?" test could report positive but the firewire is in a failing state.
T1=`plugctl -n 1 opcr[0].n_p2p_connections`
T2=`plugctl -n 1 opcr[0].channel`
if [ $T1 != "1" ] ; then
# Oops, p2p isn't one, let it go into the while loop for reset.
echo "###### Oops, p2p isn't one! Going to reset Firewire"
elif [ $T2 != "63" ] ; then
# Oops, the channel isn't 63
echo "###### Oops, the channel isn't 63! Going to reset Firewire"
else
# Now check if the firewire is primed already, then do nothing:
test-mpeg2 -r 1 > testcap.ts &
sleep 1
killall test-mpeg2
if [ -s testcap.ts ] ; then
echo "#################"
echo "# Firewire is primed!!!!!!!!!!!!"
echo "################"
# No error and
C3=0
# Don't enter the while loop, the firewire is working already...
C2=11
fi
fi
# While the counter is less then or equal to 10
# Enter the while loop and reset the firewire
while [ $C2 -le 10 ]
do
C2=$((C2+=1))
echo "##### Now Changing the Firewire setup for the $C2 time "
# First set p2p to 0 and do a capture which seems to reset everything
plugctl -n 1 opcr[0].n_p2p_connections=0
test-mpeg2 -r 1 > testcap.ts &
sleep 1
killall test-mpeg2
# Now set it to what seems to work best, at least for the DCT-6200 series tuner...
plugctl -n 1 ompr.bcast_channel=0
plugctl -n 1 opcr[0].channel=63
plugctl -n 1 opcr[0].bcast_connection=0
plugctl -n 1 opcr[0].n_p2p_connections=1
test-mpeg2 -r 1 > testcap.ts &
sleep 1
killall test-mpeg2
if [ -s testcap.ts ] ; then
echo "################"
echo "# Firewire is primed!!!!!!!!!!!!"
echo "################"
C3=0
# Exit the loop
C2=11
fi
# Otherwise repeat the loop
done
# Now print the error codes if any.
if [ $C3 -eq 1 ] ; then
echo "XXXXXXXXXXXXXXXX"
echo "X Craappp it failed after ten tries - the tuner on?"
echo "XXXXXXXXXXXXXXX"
fi
# Clean Up
rm testcap.ts
Fryfrog's Two Tuner Version
The latest version (1.0.3) is the even more, most super amazing flexible and useful firewire changing script. It supports 'p2p' as well as 'broadcast', allows many options to be fed in as -o type options and is generally better all around. It requires an external channel changing script like '6200ch' as well as the 'firewire_tester' program that comes with MythTV in the ./contrib dir. Finally, it makes use of the 'test-mpeg2' and 'plugctl' programs that come with libiec61883.
#!/bin/bash
# Released under the GPL, 2006
# Current Version: 1.03
#
# Revision history:
# Version 1.0.3, Added support for p2p *and* broadcast, using "firewire_tester"
# Version 1.0.2, Added a "seconds" option controlling how long it gets
# input from firewire before testing.
# Version 1.0.1, Improved debugging output/formatting!
# Version 1.0.0, Initial release!
#
# Remember, the -h option (and making a mistake) gives a usage summary!
#
# Firewire channel changing and test script, re-written by fryfrog at gmail.com, fryfrog.com
# Original idea from Sean Donovan, techonfoot.com
#
# This script has been completely re-written to be more robust and useful than
# the original version. It can be passed the port, node and number of tries.
# it also has a verbose and debug mode to help track down issues. The defaults
# should be very similar to the original script. Since this one can take port
# and node, the same script can be used for those with more than one fw tuner.
#
# The script also uses variables for a large portion of the script, allowing
# (hopefully) it to be much easier to change and adapt to the future or your
# needs.
#
# Requirements:
# You will need a channel changer (like 6200ch for the DCT series of STBs),
# the "firewire_tester" program that comes in ./contrib of MythTV, and finally
# the "test-mpeg2" & "plugctl" programs that should be part of libiec61883
#
# Example usage:
# 2x firewire cable boxes. `plugreport` shows them on adapter 0, node 0 & 1.
# After a bit of manual, 5 tries is found to be "ideal" and you would like
# debug messages. Script can be found in /usr/local/bin/sure-change.sh
#
# Entry in mythtv-setup, input connections, channel changing script.
# /usr/local/bin/sure-change.sh -p 0 -n 0 -t 5 -d
# Entry for second box
# /usr/local/bin/sure-change.sh -p 0 -n 1 -t 5 -d
#
# Default values for port, node, debug and verbose
# These can be changed if desired, or fed via options
MODE="p"
PORT=0
NODE=0
DEBUG=0
VERBOSE=0
TRIES=5
TIME=1
# Values for external binarys / scripts
# You probably want to point these to the correct place
CHANNEL_CHANGER="/usr/local/bin/6200ch"
FIREWIRE_TESTER="/usr/local/bin/firewire_tester"
TEST_MPEG2="/usr/bin/test-mpeg2"
PLUGCTL_PROG="/usr/bin/plugctl"
TEST_FILE="/tmp/testcap.ts"
# Lonely variable used for loop, dont touch!
X=0
# Usage function
usage() {
echo " Usage: [-p <port>] [-n <node>] [-t <tries>] [-v] [-d] [-h] <channel>"
echo " -m <mode> ** [p]2p or [b]roadcast"
echo " -p <port> ** The adapter port, default of 0"
echo " -n <node> ** The node of device, default of 0"
echo " -t <tries> ** Number of reset and test attemps"
echo " -s <seconds> ** Number of seconds to record for test, default of 1"
echo " strongly suggest something in the 1-2 range, 5 tries"
echo " with 5 second time out is 25 seconds until fail!"
echo " -v ** Verbose output"
echo " -d ** Debug output"
echo " -h ** Help and usage"
echo " <channel> ** Channel being changed to"
}
# Debug & Verbose output
inform() {
TIMESTAMP=`date +"%F %T"`
MSG="$1"
echo "${TIMESTAMP} - ${MSG}"
}
# Mode setting function
set_mode() {
MODE="$1"
if [[ "${MODE}" != "p" ]] && [[ "${MODE}" != "b" ]]; then
echo "Invalid mode specified, use [p]2p or [b]roadcast"
echo "${MODE}"
usage
exit 1
fi
(( DEBUG )) && inform "Mode used: ${MODE}"
}
# Port setting function
set_port() {
PORT=$1
(( DEBUG )) && inform "Port used: ${PORT}."
}
# Node setting function
set_node() {
NODE=$1
(( DEBUG )) && inform "Node used: ${NODE}."
}
set_p2p() {
${PLUGCTL_PROG} -p ${PORT} -n ${NODE} ompr.bcast_channel=0
${PLUGCTL_PROG} -p ${PORT} -n ${NODE} opcr[0].channel=${NODE}
${PLUGCTL_PROG} -p ${PORT} -n ${NODE} opcr[0].bcast_connection=0
${PLUGCTL_PROG} -p ${PORT} -n ${NODE} opcr[0].n_p2p_connections=1
(( DEBUG )) && inform "Default firewire settings applied to port ${PORT}, node ${NODE}."
}
reset_p2p() {
${PLUGCTL_PROG} -p ${PORT} -n ${NODE} opcr[0].n_p2p_connections=0
read_p2p
(( DEBUG )) && inform "Reset firewire settings on port ${PORT}, node ${NODE}."
}
read_p2p() {
${TEST_MPEG2} -r ${NODE} 2> /dev/null > ${TEST_FILE} &
sleep ${TIME}
killall ${TEST_MPEG2}
(( DEBUG )) && inform "Attempted read of port ${PORT}, node ${NODE}."
}
# Test firewire
test_firewire() {
# set mode, node and port options
TEST_OPTS="-${MODE} -P ${PORT} -n ${NODE}"
# set debug/verbose option
(( DEBUG )) || (( VERBOSE )) && TEST_OPTS="${TEST_OPTS} -v"
# run test with above assigned options
if [[ ${DEBUG} -eq 1 ]]; then
${FIREWIRE_TESTER} ${TEST_OPTS}
else
${FIREWIRE_TESTER} ${TEST_OPTS} 2>&1 >/dev/null
fi
if [[ $? -eq 0 ]]; then
(( DEBUG )) || (( VERBOSE )) && inform "Channel ${CHANNEL} selected and firewire working!"
go_byebye
else
(( DEBUG )) || (( VERBOSE )) && inform "Channel ${CHANNEL} selected but firewire NOT working."
fi
}
# Exit
go_byebye() {
clean
(( $1 )) && exit 1
exit 0
}
# Cleanup
clean() {
if [ -f ${TEST_FILE} ]; then
(( DEBUG )) && inform "Test file found, deleting."
rm ${TEST_FILE}
fi
}
# Begin main!
if [ $# == 0 ]; then
usage
go_byebye
fi
while getopts m:p:n:t:s:vdh OPTION;
do
case ${OPTION} in
m) set_mode ${OPTARG}
;;
p) set_port ${OPTARG}
;;
n) set_node ${OPTARG}
;;
v) VERBOSE=1
;;
d) DEBUG=1
;;
t) TRIES=${OPTARG}
;;
s) TIME=${OPTARG}
;;
*) usage
exit 0
;;
esac;
done
shift $(($OPTIND - 1))
if [ "$1" == "" ]; then
echo "You forgot to specify a <channel>!"
usage
go_byebye
else
CHANNEL="$1"
fi
clean
# Attempt to change the channel
(( DEBUG )) || (( VERBOSE )) && inform "Trying ${TRIES} times to get channel ${CHANNEL}"
${CHANNEL_CHANGER} -p ${PORT} -n ${NODE} ${CHANNEL}
(( $? )) && (( DEBUG )) && inform "External ${CHANNEL_CHANGER} failure!" && exit 1
(( DEBUG )) && inform "Initial pre-test of firewire."
test_firewire
# If fire wire isn't working, try to reset it
while [ ${X} -lt ${TRIES} ]
do
X=$((X+=1))
(( DEBUG )) && inform "Attempt ${X} of ${TRIES}..."
if [[ "${MODE}" == "p" ]]; then
# Reset p2p and do a capture, aparantly this helps with the reset.
reset_p2p
# Reset to known-good settings
set_p2p
elif [[ "${MODE}" == "b" ]]; then
# Use firewire tester to reset broadcast mode
# set mode, node and port options
TEST_OPTS="-B -P ${PORT} -n ${NODE}"
# set debug/verbose option
(( DEBUG )) || (( VERBOSE )) && TEST_OPTS="${TEST_OPTS} -v"
# run test with above assigned options
${FIREWIRE_TESTER} ${TEST_OPTS}
fi
# Test again after reset, hope it works!
test_firewire
done
(( DEBUG )) || (( VERBOSE )) && inform "${X} attempts failed, could not change to ${CHANNEL} and recieve signal via firewire"
go_byebye 1
